Chrome Stone Structural provides structural engineering for homeowners, contractors, architects and business owners across California. We prepare the structural calculations and drawings that a California building department needs to review a permit, and we stay available to answer questions while the project is built.
We work on projects throughout the state, from single-family additions to commercial tenant improvements.
Structural Engineering Services We Provide in California
- New homes and additions: foundations, wood framing, beams, posts, shear walls and hold-downs for new houses, second stories and rear additions.
- ADUs and garage conversions: structural design for detached ADUs, attached ADUs and garage-to-ADU conversions, including new footings and reinforcement of existing framing.
- Remodels and wall removals: beam and post design when a load-bearing wall is removed or an opening is widened, with the connections the plan reviewer will look for. See our article on bearing wall removal.
- Commercial tenant improvements: partition and ceiling framing, roof reinforcement, kitchen hood supports and supports for rooftop mechanical equipment.
- Retaining walls and site structures: reinforced concrete and masonry retaining walls, pool and spa support pads, fences and property-line walls.
- Patio covers, canopies and decks: wood and steel framing, footings and attachment to the existing building.
- Foundation design: continuous and isolated footings, slabs and grade beams based on the soils information available for the site.
Seismic and Lateral Design for California Buildings
Most of California sits in high seismic design categories, so lateral design is a large part of every structural set we prepare. We calculate seismic and wind forces using the current California Building Code (CBC) and ASCE 7, then design the system that carries those forces down to the foundation.
For wood-frame buildings this usually means plywood or OSB shear walls, hold-downs, straps, drag struts and diaphragm nailing. For larger openings or open floor plans we design steel moment frames or other lateral systems. Every element is shown on the drawings with the nailing, anchors and connection details the contractor needs to build it.
Building in a California Earthquake Fault Zone
The Alquist-Priolo Earthquake Fault Zoning Act, in Public Resources Code section 2621 and the sections after it, applies to projects inside an earthquake fault zone shown on the official earthquake fault zone maps, and its purpose is to keep structures for human occupancy from being built across active fault traces. For a project in a zone, the city or county must require a geologic report that defines and delineates any hazard of surface fault rupture before it approves the project; with the State Geologist’s approval, it can waive the report when it finds no undue hazard. A single-family wood-frame or steel-frame house of no more than two stories is not a “project” under the Act unless it is part of a development of four or more dwellings. Ask the planning department early whether your parcel is in a mapped zone. The geologic report comes from a geologist, and we design the structure to its findings and to the code’s seismic requirements.
Seismic Retrofits for Older California Homes
Many older California homes were built before current rules for tying the house to its foundation. The California Residential Mitigation Program’s Earthquake Brace + Bolt program describes the common weak points in wood-framed homes built before 1980 on a raised foundation:
- Bolting: anchor bolts or foundation plates connect the wood frame to the concrete foundation so the house does not slide off it.
- Cripple wall bracing: short walls in the crawl space, four feet or less, are braced with plywood or OSB so they do not collapse.
- Water heater strapping: a strapped water heater is less likely to break its water and gas lines.
Homes with taller cripple walls, hillside foundations, rooms over a garage or other irregular framing fall outside a standard brace-and-bolt layout and need an engineered design. We prepare the calculations and drawings for those cases, and for soft-story and wall-opening upgrades in homes and small apartment buildings.
What You Receive
- Structural calculations for gravity and lateral loads, organized so the plan reviewer can follow them.
- Structural drawings with foundation plans, framing plans, shear wall schedules and connection details.
- Permit documentation ready to submit with the architectural set.
- Plan check responses when the building department returns comments on the structural sheets.
- Construction-stage support to answer contractor questions and review field changes.
Structural Drawings vs. Architectural Plans
A permit set usually has two parts. The architectural plans show the layout: floor plans, elevations, sections, doors, windows and finishes. The structural drawings show how the building carries its loads: the foundation plan, framing plans, beam and post sizes, shear walls, hold-downs and connection details, backed by the structural calculations. We prepare the structural sheets and calculations, and they are ready to submit with the architectural set. The architectural plans and the site plan come from your architect or designer. Where the city asks for a soils report or a survey, those come from a geotechnical engineer or a land surveyor. If you only have a sketch so far, tell us who is preparing the architectural plans, so the two sets show the same walls, openings and dimensions.
Existing Buildings and Repair Design
Not every project is new construction. We also design repairs and changes for buildings that are already standing:
- Foundation and crack repairs: repair design for slab and wall cracks, sloping floors and sticking doors linked to settlement, expansive soil or drainage.
- Wall checks: whether a wall is load-bearing before it is opened or removed.
- New loads on an existing structure: new rooftop equipment on an existing roof.
We work from photos, measurements and any openings your contractor makes, and the result is drawings and calculations for the permit. During construction we review field changes and answer contractor questions from photos and site reports. See our article on foundation problems in California homes.
Structural Drawings for Commercial Tenant Improvements
A tenant improvement puts a new use into an existing space, and the existing structure was not always built for the new loads. Our commercial scope covers partition and ceiling framing for the new layout, roof reinforcement, kitchen hood supports and supports for rooftop mechanical equipment, with light-gauge steel for interior partitions and ceilings where it fits. In Madera, we provided the structural engineering to turn a former dental office into a 1,442 sq ft restaurant: new partition and ceiling framing, roof reinforcement where the hood and equipment loads exceeded the existing framing, hood support and bracing, and supports for the rooftop units. Read the Madera restaurant tenant improvement case study. To start, send us the floor plan, the existing drawings you have and the equipment list.
Existing Roofs and New Equipment Loads
New rooftop mechanical units, or a commercial kitchen hood hung from the structure above, add weight to a roof that was designed for its original loads. We check the existing roof framing by calculation against the new loads and, where it falls short, design the reinforcement and the equipment supports and connections. We work from the drawings and photos you supply. Useful information includes the existing structural or architectural drawings, photos of the roof framing and the existing equipment, and the new equipment’s data sheet with its operating weight, size and planned location. If the building has no drawings, measurements of the framing members and their spacing, taken by your contractor, fill the gap. For the mechanical design itself, see our MEP engineering services in California.
Materials and Structural Systems
| Material | Where we use it |
|---|---|
| Wood framing | Homes, ADUs, additions, patio covers; shear walls, hold-downs, beams and posts |
| Engineered lumber | Long beams and headers where a wall is removed or a floor spans farther |
| Structural steel | Moment frames for open fronts and wide openings, steel beams, canopies and equipment supports |
| Reinforced concrete | Footings, slabs, grade beams and retaining walls |
| Reinforced masonry | Retaining walls, property-line walls and pool walls |
| Light-gauge steel | Interior partitions and ceilings in tenant improvements |
New buildings follow the California Building Code or the California Residential Code. Work on existing buildings, such as additions, alterations, repairs and changes of use, also follows the California Existing Building Code. All three are part of Title 24 and are updated on a three-year cycle; the 2025 edition applies to permits submitted from January 1, 2026.
Deferred Submittals for Roof and Floor Trusses
Under California Building Code Section 107.3.4.1, parts of the design, such as manufactured trusses, can be sent in after the permit is issued as a deferred submittal, but only with the building official’s prior approval, and the design professional in responsible charge lists each deferred item on the construction documents. Permit Sonoma’s procedure shows what that means for trusses: the title sheet marks the trusses as deferred, the roof framing plan shows truss spacing and roof slopes, and any truss that carries load to the walls or frames resisting lateral force is identified with the drag load it must take. The truss maker’s package, with the design loads, the layout, the connections and the uplift connectors, goes first to the engineer of record, who reviews it for general conformance with the building design before it is added to the permit. We list the deferred items on our drawings, give the drag and uplift loads, and review the truss package against our design.
How a California Structural Project Works
- Project review: you send the address city, the architectural drawings or sketches and a short description of the work. We confirm the structural scope and send a quote.
- Design and calculations: we size the structural members, design the lateral system and coordinate with the architect, designer or MEP engineer.
- Drawings and permit set: we deliver the structural calculations and sheets for permit submittal.
- Plan check: we respond to the structural comments from the building department and revise our calculations and drawings.
- Construction: we stay available to the contractor for questions and changes during construction.
Already Have Plan-Check Comments?
If your project is already in plan check and the building department has returned comments on the structure, send us the comment letter, the project city and the drawings that were submitted, including any structural calculations. We read the structural comments, confirm which ones need new calculations or revised details, and tell you what the response involves before any work starts. When the structural sheets are ours, we respond to the structural comments and revise our calculations and drawings for resubmittal. If someone else prepared the structural sheets, tell us at the start, so we can confirm the scope with you and the reviewer receives one consistent set.
California Projects We Have Engineered
On a recent California project in Madera, a former dental office became a 1,442 sq ft restaurant. The existing roof framing was not designed for a commercial exhaust hood hung from above or for larger rooftop units, so we reinforced the roof where the new loads exceeded the framing and designed the hood support and bracing and the rooftop equipment supports. Read the Madera restaurant case study. Where we work: Sacramento, Los Angeles, San Francisco, San Diego, San Jose, Oakland, Fresno, Long Beach, Orange County, Riverside and Bakersfield, and other cities across the state.
Who We Work With
- Homeowners: additions, ADUs, garage conversions, wall removals, retrofits and repair design.
- Contractors and builders: permit sets, plan check responses and answers to field questions.
- Architects and designers: the structural sheets and calculations for their drawing set.
- Business owners and landlords: tenant improvements, equipment supports and changes of use.
Where we work: Sacramento, Los Angeles, San Francisco, San Diego, San Jose, Oakland, Fresno, Long Beach, Orange County, Riverside and Bakersfield, and other cities across the state.
Structural and MEP Under One Team
Chrome Stone also provides mechanical, electrical and plumbing (MEP) engineering and Title 24 energy compliance. When one team handles both the structure and the building systems, roof equipment loads, duct and pipe openings and hood supports are coordinated in the same drawing set, with one team coordinating structure and MEP.
Frequently Asked Questions
Do I need a structural engineer for my California project?
Many California building departments require structural calculations and drawings prepared by an engineer for additions, ADUs, removed load-bearing walls, retaining walls above a certain height, and most commercial work. If you are not sure, send us a short description and we will tell you what your project is likely to need.
Which parts of California do you work in?
Our office is in Sacramento, and recent projects include Cathedral City, San Jose, Madera, Redlands, Ontario and Fresno.
What do you need from me to prepare a quote?
The project city, the architectural drawings or a sketch with dimensions, photos of the existing structure for remodels, and any comments you have already received from the building department.
Can you respond to plan check comments?
Yes. Responding to structural plan check comments is part of our scope: we respond to the structural comments from the building department and revise our calculations and drawings.
Do you design seismic retrofits for older homes?
Yes. We design bolting, cripple wall bracing and soft-story upgrades, including homes that do not fit a standard brace-and-bolt layout.
Which homes need a cripple wall retrofit?
Mainly wood-framed homes built before 1980 on a raised foundation with short walls in the crawl space. A look in the crawl space, by the owner or a contractor, shows whether the walls are braced and the frame is bolted down.
Can you design repairs for cracks or damage in an existing building?
Yes. From photos, measurements and any reports, we check the foundations, framing and damaged members by calculation and prepare repair drawings where they are needed.
Which code applies to work on an existing building in California?
The California Existing Building Code, together with the Building or Residential Code for the new parts. The 2025 edition applies to permits submitted from January 1, 2026.
Do you design in steel and masonry as well as wood?
Yes. We design wood, engineered lumber, steel, concrete, masonry and light-gauge steel, depending on the project.
What is a soft-story building?
A soft-story building is a wood-frame building of more than one story whose ground floor has large openings and few solid walls, such as tuck-under parking, garage doors or wide shop windows. California cities call these soft, weak or open-front wall lines. The lower story is weaker than the floors above it, and the City of Pasadena notes that soft-story buildings caused significant loss of life and property damage in the 1989 Loma Prieta and 1994 Northridge earthquakes. A retrofit strengthens that level, usually with new shear walls or steel frames.
Is a soft-story retrofit required in California?
It depends on the city. California Assembly Bill 304 of 2005 encourages cities to require retrofits of soft-story buildings built under codes older than 1978, and each city sets its own rules. Pasadena’s mandatory ordinance, adopted in May 2019, covers wood-frame buildings permitted on or before November 12, 1976 with parking or similar open space at the ground floor, and excludes single-family homes and parcels of four or fewer units. Burbank runs a mandatory program for older multi-family buildings with tuck-under parking or a weak front story, while the Long Beach program is voluntary.
How do I find out if my building is on a soft-story list?
Check with the city where the building stands. Long Beach publishes an online map of residential buildings with possible soft, weak or open-front conditions, compiled from public property and permit records, satellite maps and street views, and owners can return a form to confirm or correct the entry. Pasadena mailed a notice and order to the owners of affected properties and accepts an optional screening form from owners who believe the building is exempt. In Burbank, the screening form comes first, followed by engineered retrofit plans. We prepare those calculations and drawings for the permit.
Does a retaining wall need a permit in California?
Usually, once it is taller than 4 ft. Sacramento and Berkeley, for example, exempt a retaining wall that is not over 4 ft high, measured from the bottom of the footing to the top of the wall, unless it supports a surcharge such as a slope, a driveway or a building above it. Berkeley also excludes walls that hold flammable or combustible liquids, and asks for a zoning permit for a wall in a required setback. A taller retaining wall needs a permit, and we prepare its structural design and calculations.
How big a shed or deck can I build without a permit in California?
In Sacramento and Berkeley, a one-story detached accessory structure, such as a tool or storage shed, is exempt when its floor area is not over 120 sq ft. A deck is exempt when it is not over 200 sq ft, no more than 30 inches above grade at any point, not attached to the house and not serving a required exit door. Exempt work must still follow the California building code and city rules, Berkeley notes that a zoning permit may still apply, and Sacramento’s exemptions do not apply in a design review or preservation district or to a historic landmark.
Sources
- California Building Standards Commission, California Building Standards Code (Title 24)
- California Residential Mitigation Program, Earthquake Brace + Bolt Retrofit
- California Energy Commission, 2025 Building Energy Efficiency Standards
- City of Pasadena, Soft-Story Retrofit Ordinance
- City of Burbank, Soft-Story Seismic Retrofit
- City of Long Beach, Building Seismic Resiliency Program
- City of Berkeley, Work Exempt from Building Permits
- City of Sacramento, Required Building Permits
- Permit Sonoma, 9-4-20 Deferred Truss Submittals
- California Legislative Information, Public Resources Code Section 2621.5
- California Legislative Information, Public Resources Code Section 2621.6
- California Legislative Information, Public Resources Code Section 2623


