Florida Restaurant Tenant Improvement: MEP Checklist

Specialty ice cream shop tenant improvement in Gibsonton, Florida with MEP design by Chrome Stone

Short answer: a restaurant, café or dessert shop that moves into an existing retail space in Florida usually needs mechanical, electrical and plumbing (MEP) drawings before the building department will issue the permit. The drawings show the cooling and ventilation, any kitchen exhaust and make-up air, the electrical load and panel changes, and the sinks, water heating, drains and grease management. Collecting the existing conditions and the equipment list early is the surest way to a complete set.

Kitchens need exhaust and make-up air, refrigerated cases and cooking equipment need power, and new sinks need water and drains. This checklist covers what an MEP engineer looks at on a Florida food-service tenant improvement, often called a build-out, so you can collect the right information early and avoid surprises once the lease is in place.

1. Start With the Existing Conditions

  • Electrical service: the size of the existing service and panel, and whether there is room for the new loads.
  • HVAC equipment: the age, capacity and location of the existing rooftop or split units.
  • Plumbing: where the water supply and sanitary lines are, and how far the new fixtures will be from them.
  • Roof: whether new exhaust fans or equipment can be added, which may also need structural review.

Photos of the electrical panel labels, the HVAC nameplates and the ceiling space are very useful at this stage.

2. Mechanical: Cooling, Ventilation and Exhaust

Florida’s heat and humidity make cooling loads high, and kitchens add heat from cooking and refrigeration equipment. The mechanical design sizes the cooling equipment for the space, provides the outdoor air required for the occupants, and controls humidity so that display cases and dining areas stay comfortable. It is one of the first checks we run on Tampa Bay restaurant build-outs.

If the menu needs a cooking hood, the design must balance the hood exhaust with make-up air so the space does not run under negative pressure. Restrooms and storage rooms need their own exhaust.

3. Electrical: Equipment Loads and Panels

Refrigerated display counters, freezers, ice machines, mixers and cooking equipment can add a large electrical load. The electrical design includes a load calculation to confirm the service can carry it, panel schedules with the new circuits, and lighting and power plans for the dining, service and preparation areas. If the existing service is too small, the design shows the upgrade.

4. Plumbing: Sinks, Water Heating and Drains

Food-service spaces usually need hand sinks, preparation sinks, a mop sink and dishwashing, along with water heating sized for them. The plumbing design shows the water supply, sanitary waste and vent piping, and the fixture and equipment connections. Many jurisdictions also require grease management for kitchens, which affects the drain layout.

5. Coordinate With the Layout and the Structure

The MEP drawings must match the architectural floor plan and the equipment list. When rooftop units or exhaust fans are added, the roof framing may need to be checked or reinforced, and in Florida the equipment must be anchored for wind. When one team handles the MEP and structural work, those pieces stay consistent.

What the Permit Set Usually Includes

Requirements vary by city and county, so always check the local submittal list. As one example, the City of Tampa’s commercial alteration submittal document asks for items such as:

  • Mechanical plans with the equipment layout and loads.
  • Electrical load calculations and panel schedules.
  • Plumbing plans, including grease traps where they apply.
  • Energy calculations when HVAC work is part of the scope.

Our article on restaurant tenant improvement MEP permit sets in Florida walks through the full set sheet by sheet.

State Food Service Plan Review

A restaurant in Florida answers to two reviewers. The local building department reviews the building permit, including the MEP drawings. The state’s Division of Hotels and Restaurants, part of the Department of Business and Professional Regulation, oversees public food service establishments, and Florida law gives it authority over plan approvals and plan reviews for them. Ask the division early whether your project needs its plan review, and keep the equipment list, sink layout and plumbing fixtures the same in both submittals.

Other Approvals Besides the Building Permit

  • Fire review: kitchen hood suppression, fire alarm changes and sprinkler work are often reviewed separately, so coordinate them with the hood and exhaust design.
  • Local use approvals: some cities require a separate approval for the use of the space before the business opens. Check with the city when the space changes from retail or another use to food service.
  • Utility requirements: water and sewer providers can have their own rules for grease interceptors, backflow prevention and meter sizes.
  • Landlord approval: many leases require the landlord to approve the drawings, rooftop equipment locations and roof penetrations before the permit is submitted.

Starting these in parallel with the MEP design avoids late changes to the permit set.

Fire Protection and Life Safety Coordination

A restaurant often changes how many people the space holds and how the kitchen is used. That can affect exit signs and emergency lighting, the fire alarm, the sprinkler layout around new walls and ceilings, and the fire suppression system that protects a cooking hood. These items are often designed by specialty contractors, but the MEP drawings must leave room for them and match their locations.

Common Mistakes

  • Committing to the lease before checking whether the electrical service can carry the kitchen.
  • Choosing cooking equipment before deciding whether a hood is needed and where it can exhaust.
  • Forgetting make-up air, which leaves doors hard to open and the hood unable to capture smoke.
  • Placing new sinks far from the existing drains without checking the slab and the slope.
  • Adding rooftop equipment without a structural check and wind anchorage.

A Real Example: Ice Cream Shop in Gibsonton

In Gibsonton, in Hillsborough County near Tampa, Chrome Stone designed the MEP systems for a 796 sq ft tenant improvement that turned an existing retail space into a specialty ice cream shop. The design covered HVAC, plumbing and electrical systems for the customer seating, refrigerated display counters, preparation and service areas, storage and utility spaces. Across the bay, we prepare the same drawings for restaurant build-outs in St. Petersburg and Pinellas County.

What to Send Your MEP Engineer

  • The address and the landlord’s information about the space.
  • The floor plan and the equipment list with model numbers.
  • Photos of the electrical panel, HVAC equipment and ceiling space.
  • The menu or a description of the cooking, which decides whether a hood is needed.

For food-service and retail spaces in Miami-Dade County, our page on Miami structural and MEP services covers the local building departments and MEP design.

How Chrome Stone Can Help

Chrome Stone Structural provides MEP and structural engineering for Florida tenant improvements, with permit drawings. See our MEP engineering services in Florida and our engineering services in Tampa. We also prepare tenant improvement drawings for restaurants in West Palm Beach, Jacksonville and Orlando.

Frequently Asked Questions

Does a restaurant build-out in Florida need MEP drawings?

In most cases, yes. New kitchen equipment, sinks, exhaust and electrical loads change the building’s systems, and building departments usually ask for mechanical, electrical and plumbing plans before they issue the permit.

Does every restaurant need a kitchen hood?

No. It depends on the cooking. Equipment that produces grease-laden vapors usually needs a hood, while some shops that only reheat or serve prepared food may not. Share the menu and equipment list with your engineer early.

What is make-up air?

It is outdoor air brought in to replace the air a kitchen hood exhausts. Without it, the space runs under negative pressure and the hood does not work well.

Can my existing electrical panel handle the new equipment?

Only a load calculation can tell. The engineer adds the new equipment to the existing loads and checks the service and panel. If they are too small, the drawings show the upgrade.

Does a Florida restaurant need a state plan review?

Many do. The Division of Hotels and Restaurants handles plan approvals for public food service establishments. Ask the division early whether your project needs one, in addition to the building permit.

Sources

We post one project and one code or engineering note every week on LinkedIn. Follow Chrome Stone on LinkedIn

Request a Quote

Discuss your engineering project

Tell us where your project is located in California or Florida and which engineering services you need.

  • Project city and state
  • Building type and proposed work
  • Required engineering disciplines
  • Architectural or existing-condition drawings available

Prefer to call? +1-279-221-5279


    We will use this address to respond to your inquiry.


    Add it if you prefer a call back.


    City only. A full property address is not needed for this first inquiry.

    Engineering support needed

    California Title 24 applies to California projects only.


    Briefly describe the building, proposed work, and any questions. Do not include passwords, payment details, or confidential documents.

    Add project stage or other details (optional)


    Leave blank if unknown.


    Tell us what the date relates to. The team will confirm feasibility after reviewing the scope.

    We use these details to review and respond to your inquiry. Read our Privacy Policy.

    While we review your project, follow Chrome Stone Structural on LinkedIn for new projects and code updates. Follow us on LinkedIn