Wind load calculations in Florida start from one fact: the building code is shaped by hurricanes, and on most Florida projects wind is the load that controls the structural design. Chrome Stone Structural prepares wind load calculations and wind-resistant structural designs for homes, additions, canopies, screen enclosures, rooftop equipment and commercial buildings across Florida, including projects in the High-Velocity Hurricane Zone (HVHZ).
We work on projects across Florida, and our Florida structural engineering page covers the work statewide.
Wind Load Calculations
We calculate design wind pressures using ASCE 7 and the current Florida Building Code (FBC). The calculation starts from the basic wind speed for the site and the building’s risk category, then accounts for exposure, building height, roof shape and the location of each element on the building.
- Main wind force resisting system pressures for the overall structure.
- Components and cladding pressures for roof sheathing, roof framing, walls, and window and door openings, including the higher pressures at roof edges and corners.
- Rooftop equipment wind forces for anchoring HVAC units and other equipment.
- Open structures such as canopies, carports and screen enclosures.
From Wind Speed to Wind Pressure
Wind maps give a design wind speed in miles per hour, but structures are designed for pressure, in pounds per square foot. Pressure rises with the square of the wind speed, so a small increase in design speed means a much larger increase in load. The calculation then adjusts that pressure for the building’s exposure, height, shape and the part of the building being designed. That is why two houses on the same street can have different design pressures for their windows, and why a corner window needs a higher rating than a window in the middle of a wall.
What Goes Into a Florida Wind Load Calculation
Wind design in Florida follows the wind provisions in Chapter 16 of the Florida Building Code. According to the Florida Building Commission, the 8th Edition (2023) took effect on December 31, 2023, and the Commission has posted materials for the 2026 update, so we confirm the edition for each permit. Every calculation starts from the same inputs:
- Design wind speed for the site, from the code’s wind speed maps.
- Risk category, based on the use of the building: a house, a school or an emergency facility are treated differently.
- Exposure category, based on the surroundings: open water and open land produce higher pressures than a dense suburb.
- Building height, roof shape and slope, and whether the building is enclosed or partially open.
- Topography, where hills or bluffs speed up the wind.
Main Structure vs Components and Cladding
A wind load calculation looks at the building at two scales. The main wind force resisting system is the frame, walls, roof diaphragm and foundation that hold the whole building up against wind. Components and cladding are the smaller pieces the wind pushes and pulls on directly: roof sheathing, trusses and their straps, windows, doors, soffits and wall panels. Components see higher pressures than the building as a whole, and the highest pressures act at roof edges, corners and wall corners. Our drawings show these zones so the roofer, the window supplier and the framer each know what their part must resist.
What Changed for Roofs in the 2023 Code
The 8th Edition (2023) Florida Building Code references ASCE 7-22, and the Florida Building Commission’s fact sheet lists several changes to roof wind loads. For gable and hip roofs with slopes over 7 degrees, the roof zones were reduced to 3 for all roofs. Design pressures for many roof zones went down, but for some zones they are unchanged or slightly higher.
Roof overhangs are handled differently too. The overhang pressure is now found by adding the coefficient for the roof area above the overhang to the coefficient for the adjacent wall. The Florida Building Code, Residential has a simplified method for buildings with mean roof heights of 60 feet or less. Older roof pressure tables should not be reused without checking them against the current edition.
Windows, Doors and Garage Doors
Every exterior window, door and garage door in Florida needs a design pressure rating that meets or exceeds the calculated pressure at its location. We prepare pressure tables for each opening, so products can be chosen before the permit is submitted. The product itself must carry a Florida Product Approval or a Miami-Dade Notice of Acceptance; in the High-Velocity Hurricane Zone of Miami-Dade and Broward, the approval must cover HVHZ use. Garage doors are large and flexible, so they often govern the design of the wall around them as well.
Rooftop Solar Panels and Wind Load
A rooftop solar array adds weight to the roof and catches wind, and the racking passes those forces into the roof framing. Hillsborough County’s solar photovoltaic checklist shows what this means at permit time. Roof-mounted systems are permitted as an electrical trade permit, but the plans must show conformance with the Florida Building Code sections on roof load, wind load, roof access and pathways, and roof setbacks. The checklist also asks the engineer to confirm that the building and site elements can carry the added loads from the solar components.
The County adds design requirements for properties in the wind-borne debris region, and for mobile and manufactured homes it asks for an engineer’s letter on the structure and mounting system, with no equipment attached to the exterior walls. Our wind design for a solar array covers the uplift and downforce on the modules, the attachment of the racking to the rafters or trusses, and the check of the existing roof framing, from the drawings, photos and roof details the owner or installer sends.
Wind-Borne Debris and Impact Protection
Much of coastal Florida is in the wind-borne debris region, where glazed openings must be protected from flying debris during a hurricane. Owners can use impact-resistant windows and doors or approved shutters. Hillsborough County, for example, explains that the building’s risk category and whether the design wind speed is 140 mph or greater must be determined first, to decide whether openings need protection. Inside the HVHZ, impact protection rules are stricter still. We identify whether the site is in the debris region and show the protection requirement on the drawings. Our article on the High-Velocity Hurricane Zone explains the HVHZ rules in more detail, and our article on Florida wind load requirements covers the basics for owners.
A Continuous Load Path
Wind design only works if every connection between the roof and the foundation can carry the uplift and lateral forces. We design and detail that load path: roof sheathing attachment, truss and rafter uplift connectors, top plates or bond beams, reinforced masonry cells or wood shear walls, and anchorage into the tie-beams and foundation. The drawings show each connection so the contractor and the building department can check it during construction.
Manufactured Homes: Anchors and Tie-Downs
Mobile and manufactured homes in Florida are installed under their own state rules, not the site-built provisions of the Florida Building Code. Chapter 15C-1 of the Florida Administrative Code sets the installation standards, including Rule 15C-1.0103 for foundations and piers, Rule 15C-1.0104 for anchors and tie-downs, and Rule 15C-1.01031 for HUD homes in Exposure D areas.
Engineering comes in where a project goes beyond the standard installation: an addition, carport or porch attached to the home, a raised foundation in a flood zone, or a site condition the standard details do not cover. In those cases, the engineer designs the attached structure for Florida wind loads so it does not add uplift to the home’s own tie-downs.
Screen Enclosures and Sunrooms in High Wind
Aluminum screen enclosures over pools and patios are light, but they cover a large area, so wind is what controls their design. Miami-Dade County’s product control checklist for screen enclosures shows what the structural design has to answer. It asks for calculations showing that the product, including the footing and anchorage, can withstand the forces in the Florida Building Code. It lists checks under a design pressure: bending, shear, axial and combined stresses on the frame, deflection limits, foundation support and overturning of the whole structure, and the loading on screws, bolts and connectors.
When a screen room becomes a sunroom or glass room, the design changes. Hillsborough County asks for the risk category of the structure to be shown on the plans of screen enclosure and glass room additions. A glass room catches more wind than a screened space, because screen lets some of the wind pass through, so the connection to the house and the slab or footing below has to be checked for those loads.
Gable End Walls in High Wind
A gable end wall is tall and flat, and it is often braced only at its top by the roof and ceiling framing. In hurricane winds it takes direct pressure on one side and suction on the other, so a weak connection at the top can let the wall fold in or out and open the roof. Section 553.844 of the Florida Statutes lists prescriptive gable-end bracing among the wind mitigation techniques for site-built single-family homes built before the Florida Building Code.
For a new design or a retrofit, the engineer checks how the gable wall is tied to the ceiling and roof framing, adds bracing that carries the wind load back into the roof and ceiling diaphragms, and details the connections at the top and bottom of the wall.
Can an Older Wind Design Be Reused?
A wind design from an earlier permit is not automatically valid for a new one. The Florida Building Commission updates the code on a regular cycle, and the wind speed maps changed in some areas with the 2023 edition. The building department reviews new work under the edition it enforces when the application is filed.
Before reusing older drawings, check four things: the code edition now in force, the current design wind speed and exposure for the site, the building’s risk category, and any changes to the building itself, such as new openings, a new roof or added rooftop equipment. When any of these has changed, the wind loads are calculated again for the new permit.
High-Velocity Hurricane Zone (HVHZ)
Miami-Dade and Broward counties are in the HVHZ, where the Florida Building Code adds stricter requirements for structural design, materials and building envelope products. For HVHZ projects we prepare the structural set with those requirements in mind and list the design pressures that the windows, doors and other envelope products must meet, so the product submittals can be checked against them. See our Fort Lauderdale page for Broward projects. Outside the HVHZ, Gulf Coast projects in Naples, Fort Myers and Cape Coral still face high design wind speeds.
On the Gulf coast, our page on engineering services around Tampa Bay covers storm repairs, flood zones and local permits.
Typical Wind Design Projects
- Additions and renovations that add or change roof framing.
- Steel and aluminum canopies, carports and patio covers.
- Screen enclosures, pool enclosures and lanai roofs.
- Rooftop equipment supports and anchorage for HVAC replacements.
- Commercial tenant improvements with new roof openings or equipment.
- Design pressure schedules for window and door replacements.
What You Receive
- Wind load calculations for the structure, its components and its equipment.
- Structural drawings with connection details, uplift schedules and anchorage.
- Design pressure schedules for openings where the project needs them.
- Permit documentation from an engineer.
- Plan review responses when the building department returns comments.
Frequently Asked Questions
Is my project in the High-Velocity Hurricane Zone?
The HVHZ covers Miami-Dade and Broward counties. Projects elsewhere in Florida follow the standard wind provisions of the Florida Building Code, which still require wind design for the site’s wind speed and exposure. On the Gulf Coast, see our structural engineer in St. Petersburg page.
Do I need wind load calculations for a window or door replacement?
Many Florida building departments ask for the design pressures of replacement windows and doors. We can prepare a design pressure schedule for the openings in the project.
Can you design anchorage for rooftop HVAC equipment?
Yes. We calculate the wind forces on the equipment and design the supports and anchorage, and on projects where we also design the MEP systems we coordinate the equipment selection with the structure. Inland sites need it too; see our structural engineer in Orlando page.
What do you need from me to prepare a quote?
The project address city or county, the drawings or photos of the structure, and a short description of the work.
How do you convert wind speed in mph to pressure in psf?
Pressure rises with the square of the wind speed and is then adjusted for exposure, height, building shape and the location on the building. The result is a different design pressure for the main structure, each roof zone and each opening.
Why does a corner window need a higher rating?
Wind pressures are highest at wall corners and roof edges, so openings and roofing in those zones must resist higher loads than those in the middle of a wall or roof.
Do I need impact windows or shutters?
In the wind-borne debris region, glazed openings need impact-resistant products or approved shutters. We confirm whether your site is in that region.
Which code edition do you use for wind loads?
The Florida Building Code edition that applies to the permit. The Florida Building Commission lists the 8th Edition (2023), effective December 31, 2023, and has posted materials for the 2026 update.
Did the Florida wind speed maps change with the 2023 code?
Only in part of the state. The Florida Building Commission’s fact sheet on ASCE 7-22 says that wind speeds on the peninsula are unchanged and have effectively not changed since the 2010 code. In the western panhandle they increased, and for Risk Category IV buildings they decreased slightly in the Big Bend area. Older drawings from the panhandle should be checked against the current maps.
How do I find the design wind speed for my address in Florida?
The Florida Building Code wind speed maps set the ultimate design wind speed by location and by the building’s risk category. The 8th Edition (2023) also added a note that allows site-specific wind speeds from the ASCE 7 Hazard Tool, where you enter an address or coordinates. Your county building department can confirm the value it expects for your parcel, and we show it on the drawings.
What wind information has to be on the permit drawings?
Building departments ask for the design criteria on the drawings. Hillsborough County lists the risk category, the design wind speed, the exposure type, the internal pressure coefficient, the components and cladding design pressures in psf, and the codes used. Orange County’s permitting glossary asks for the basic wind speed, wind exposure, internal pressure coefficient and components and cladding. Our wind load calculations provide each of these values.
What is Florida Product Approval, and how does it relate to wind loads?
Florida law sets up a statewide system for approving building products. It covers categories such as exterior doors, windows, shutters, skylights, roofing, panel walls and structural components. Each approval lists the product’s rated performance, and the design pressure from the wind calculation has to be within it. Orange County, for example, asks for the manufacturer’s installation details with the Florida Product Approval number or the Miami-Dade Notice of Acceptance. Approvals can be searched on the Florida Building Commission’s product approval site.
Is a wind mitigation form the same as a wind load calculation?
No. The state’s uniform mitigation verification form (OIR-B1-1802) records the wind-resistant features of an existing home so the owner can ask an insurer for premium savings, and the state insurance regulator says it stays valid for up to five years unless the structure changes. A wind load calculation is a design document. It sets the pressures that new or altered construction must resist, and it goes with the permit drawings.
Sources
- Florida Building Commission, Florida Building Code Information
- The Florida Senate, Florida Statutes Section 553.73 (2025), Florida Building Code
- Florida Building Commission, High-Velocity Hurricane Zone provisions (Chapter 16, code development text)
- Florida Building Commission, Product Approval
- Miami-Dade County, Windows, Shutters and Doors
- Florida Building Commission, ASCE 7-22 Wind Loads Fact Sheet (PDF)
- Hillsborough County, Residential Structural Design Criteria
- Orange County, Glossary of Permitting Terms
- The Florida Senate, Florida Statutes Section 553.842 (2025)
- Florida OIR, Wind Mitigation Resources
- Florida Administrative Code, Chapter 15C-1
- Florida Senate, Florida Statutes 553.844 (2025), Windstorm loss mitigation; requirements for roofs and opening protection
- Hillsborough County, Solar Photovoltaic System Checklist
- Miami-Dade County, Product Control Section, Checklist for the Approval of Screen Enclosures (PDF)
- Hillsborough County, Residential Screen Enclosure & Glass Room Additions


